Hello

WARNING:

-Any observation of numbness, tingling, excess coldness, or color changes to blue/black should not be ignored and are signs to release air pressure and remove the device as soon as possible. Restore circulation before continuing to use product. Be aware of your feet and objects beneath the device during operation. 

​

1. Make sure the knob is set to the OFF (left, counter-clockwise position) and all air has left the device.

​

2. Be partly or fully soft/flaccid to insert into the device.  Device should be used dry. You can use soapy water to aid with lubrication for insertion, but be sure to dry off fully. Using lotions may cause slippage during operation.

​

3. If uncircumcised (uncut), be sure the foreskin is covering the head (glans) and insert it into the opening. The head will pop out of the foreskin on the other side of the clamp opening.  If circumcised, use two fingers to compress and pull the head through the device opening.  Soapy water can be used to lubricate the device opening for easier insertion.  Remember to dry off the water before step 4. 

​

4. Slide the device all the way down to the shaft base, resting at the bottom. 

​

5. Gently turn the knob to the ON (right, clockwise position) to close the air valve. Do not overtighten the knob as it can damage the air valve.

​

6. Slightly pump the clamp's air bulb to form a seal around the shaft. Observe for leakage or misalignment.

​

7. Pump the air bulb until a solid grip pressure is felt on the shaft. No pain should be felt. NEVER pump to maximum pressure!

​

8. Gently apply tension to test grip strength before adding any weight or letting it hang by itself from the shaft. 

​

9.  If this is your first time using, carefully lower the weight by itself (nothing attached to the hook) testing the grip strength as its lowered. Be aware of your feet and other objects beneath the weight and protect as needed. The device is meant for long hours of wear, so avoid the temptation to use more than 4-6 lbs in total weight including the 2 lb frame. The device is not designed as a compression/heavy weight hanger. Loading more weight does not speed up results and can potentially cause injury.

 

10.  Do not adjust device air pressure unless pressure loss or slippage is felt. If you begin to get erect while wearing, release the air pressure and let it pass and focus on the rection subsiding. Do not get fully erect in the device if possible. The air bulb must remain plugged into the device for it to operate as advertised. 

​

11. Be on constant watch for any signs of pain, tingling, numbness, excess cold, or color changes to blue/black. Should you sense any of these signs, release air pressure and remove the device immediately to restore circulation. As you become familiar with the device, releasing just the air pressure will work to restore circulation. If sitting, hang the device over the edge of the chair to keep constant tension.  The device works best while standing/walking when worn under clothing. 

​

12. To remove, use soapy water around the opening and shaft for lubrication. Wash device before re-use with mild dish washing liquid, no hard chemicals that may damage silicone.

 

13. Should you need to urinate with the device on; hold the device up with one hand and release the air with the other hand.  Urinate, then add air pressure again to grip the penis. Lower the device down.

​

14. The sleeve can be removed quickly to clean. Simply remove the velcro bands and lift the sleeve off the metal frame. Remember to wash your device to avoid bacteria growth and avoid urinary tract infections. Do not use harsh chemicals, only mild dish soap or hand soap. 

​

Suggested usage                                       

​

-Take good measurements and even photos before you begin to compare your progress to.

 

-Time under tension is key.  Strive for as many hours as you can under tension, avoiding rest days when possible.

 

-Remove the device once an hour to check things and restore circulation, at least until you become familiar with the device's operation.

 

-Avoid the temptation to load on high weight, as it will only increase the likelihood of strengthening your ligaments and make ongoing results less likely to occur.

 

-Start with only 1-2 lbs, working up to 4-5 lbs as your body adapts to the weight.  Over the course of long hours, soreness will begin to occur to the point of being uncomfortable and burning at the base and shaft may also be observed. This is normal, and to be expected with ongoing growth. 

​

-Allow 4-6 weeks of constant use before beginning to measure for results. Measure at the beginning of each month and only adjust your weight/time under tension if you are not seeing results changing from one month to the next. 

​

-Above all, be patient and understand that PE is a slow process.  Treat it like a lifestyle or hobby that you devote time to, like any other hobby. 

​

​

Tips and Tricks

​

Any numbness, tingling, excess coldness, or color change to blue/black should not be ignored and are signs to remove the device as soon as possible. 

​

The device is best worn with dry skin.

​

ALWAYS wash hands and devices before beginning a PE session to avoid urinary tract infections.

​

Avoid performing any manual stretching, since it will strengthen the ligaments and tissues, making your device less likely to be effective. 

​

Never wear while sleeping or impaired by drugs or alcohol.

​

Color changes to blue or black indicate lack of oxygen and to remove the device immediately. 

​

Do not pump to excess pressure, and never to the point of pain.  The device should hold on without pain.

​

Trim pubic hair and avoid using lubrication to avoid slippage.

​

Time under tension is key.  The longer it can be worn the better the results.

 

Strive for at least 2 hours wear daily with as few off days as possible for optimum wear. 

​

An Air-Lock Clamp worn for a few minutes before wearing the JackHammer can help weaken tissues and improve length progress, referred to as ShockLoading in the PE world. 

​

For more gripping power, zipties or twist ties (not included) can be added over the rubber where the groove rings are located. As seen here: